Question 1

1. What media types can I use with the SU flowmeter?

Accepted Answer

The SU series can be used with different media types and is sorted by part number. Please use the chart below to pick out an option based on your media.

SUxx2x: 90% water solutions (conductive or non-conductive)
SUxx3x: 35% glycol solutions and oil media from 7…68 mm²/s at 40°C
SUxx5x: 90% water solutions (conductive or non-conductive) and 35% glycol solutions and oil media from 7…68 mm²/s at 40°C with 8...32VDC operating voltage and no display.
SUHxxx: 90% water solutions and food oils from 30…68 mm2/s at 40°C
SUWxxx: 90% water solutions (conductive or non-conductive)
SUCxxx: 90% water solutions (conductive or non-conductive)

Check out the "Select by application" page to see other flow technologies available.

Question 2

2. How to program the SU sensors with LED display?

Accepted Answer

General use of pushbuttons

Press Mode/Enter (M/E) until desired parameter is displayed.
Press Set (S) to display the current setting.
To change setting, press and hold the Set (S) button until the display stops flashing. Then press Set (S) to toggle through options.
When desired value is reached, press Mode/Enter (M/E) to confirm the setting.

The following illustrate the most common programming required for flow meter applications. Refer to the Operating Instructions manual found under the "Downloads" tab at the product datasheet page for more details on these and other features.

Scale the analog signal (output 2 only)

Press M/E until "ou2" is displayed.
Press S until "I" (4...20 mA analog current) or "U" (0...10 VDC for analog voltage) is displayed.
Press M/E to confirm setting.
Press M/E until "ASP" is displayed.
Press S to enter the value representing the analog start point (4 mA / 0 VDC).
Press M/E to confirm setting.
Press M/E until "AEP" is displayed.
Press S to enter the value representing the analog end point (20 mA / 10 VDC).
Press M/E to confirm setting. After 15 seconds, the meter returns to normal run mode.

Note that the minimum distance between ASP and AEP is 20% of the full measuring range of the meter.

Setup totalizing function (output 1 only)

Press M/E until "ou1" is displayed.
Press S until "ImP" is displayed. This is the pulse output setting.
Press M/E to confirm setting.
Press M/E until "ImPS" is displayed. The is the volumetric pulse value.
Press S until the desired volume per pulse is displayed.
Press M/E to confirm setting.
Press M/E until "ImPR" is displayed. Set to "YES" for a pulse every time volume (ImPS) set above flows through the meter. Set to "NO" for a single pulse when the volume (ImPS) above flows through the meter.
Press S to confirm setting. After 15 seconds, the meter returns to normal run mode.

Question 3

3. What is the ZH4217 and how do I use it or another external pushbutton to reset the totalizer?

Accepted Answer

The ZH4217 is a kit consisting of:

A KTE301 pushbutton
EVC847 y-splitter.
EVC010 0.3m patchcord

Setup

On the SU, change OU2 to [In.D] and Din2 to [HIGH] using the step-by-step procedures below. These procedures should be used with any external pushbutton reset.
When using the ZH4217, connect the KTE301 to channel B of the EVC847 using the EVC010, and connect the SU sensor to channel A. Then connect power to channel C, with pin 1 to +24 VDC and pin 3 to ground.

The totalizer will be reset to zero when the pushbutton is pressed.

For 3-pushbutton SUs

Press Mode / Enter button to enter menu.
Press [▼] to EF, press mode enter button.
Press [▼] to OUT2, press mode enter button.
Press [▼] to ou2, press mode enter button.
Press and hold [▲] or [▼], the display will begin to flash. Keep [▲] or [▼] pressed until [In.D] is displayed. Release and briefly press mode enter. (ou2 will be displayed)
Press [▼] until DIn2 is displayed. Briefly press mode enter.
Press and hold [▲] or [▼], the display will begin to flash. keep [▲] or [▼] pressed until [HIGH] is displayed. Release and briefly press mode enter.

For 2-pushbutton SUs

Press Mode / Enter button to enter menu.
Press Mode / Enter button to OU2, press set button.
Press and hold set button the display will begin to flash. Keep Set button pressed until [In.D] is displayed. Release and briefly press Mode / Enter. (OU2 will be displayed)
Press Mode / Enter button until DIn2 is displayed. Briefly press Set button.
Press and hold Set button; the display will begin to flash. Keep Set button pressed until [HIGH] is displayed. Release and briefly press Mode / Enter.

Question 4

4. Can the SU flow sensor be used in sanitary applications?

Accepted Answer

Yes, the SUHxxx sensors are suited for sanitary applications with 90% water and food oils from 30...68mm²/s at 40°C. They have FDA, NSF, and 3A approvals and are supplied with Tri-clamp fittings.

SU ultrasonic flow meter: Frequently-asked questions

SU Ultrasonic flow meters: Overview

Benefits of ifm's IO-Link ultrasonic flow meters

SU Ultrasonic flow meters: Applications