Certificates / Protocols

• Service free of charge from the ifm group of companies
• Multi-point factory certificate available as PDF document, also after the unit has been ordered
• Languages: in two languages English/German
• For selected products:
  Available for the following product series:
  • LDLxxx
  • PI27xx, PI28xx, PM1xxx, TA20xx, TA22xx, TA25xx, TA28xx, TD22xx, TD25xx, TD28xx,
  • TD29xx (manufactured as of 01/2018)
  • PG27xx, PG28xx (manufactured as of 01/2019)
  • SM6x2x, SM7x2x, SM8x2x
  • SDx500, SDx600 (issue only possible for air characteristics)
  • TA11xx, TA13xx und TCCxxx

Manufacturer's certificate EN10204-2.1 (order code ZC0001)
(according to DIN50049-2.1)

• Certifies that the listed articles / article groups conform to the indications in the corresponding data sheet and have been subjected to a 100 % final test.
• The document is bilingual (German / English).

Manufacturer's certificate EN10204-2.2 (order code ZC0002)
(according to DIN 50049-2.2)

• Certifies that the listed articles / article groups conform to the indications in the corresponding data sheet and have been subjected to a 100 % final test.
• Annexes: description of the 100 % tests
• The document is bilingual (German / English).

The following documents are available for selected fluid sensor products:

Inspection certificate material EN10204-3.1 (order code ZC0003)
(according to DIN 50049-3.1)

• Results of batch-related tests to prove that the requirements regarding the material characteristics and quality are met.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.

• Only issued for fluid sensor products (list of products).

ISO calibration protocol pressure (order code ZC0004)

• Calibration certificate
• 6 calibration points in steps of 20 % of the measuring range. Other calibration points possible on request.
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for pressure sensors  (list of products).

DAkkS calibration protocol pressure sensors (order code ZC0005)

• DKD/DAkkS certificate (DAkkS = Deutsche Akkreditierungsstelle)
• 11 calibration points. Further calibration points possible on request.
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for pressure sensors (list of products).

DAkkS calibration temperature sensors 3-point (order code ZC0013)

• DKD/DAkkS certificate (DAkkS = Deutsche Akkreditierungsstelle)
• Comparative calibration in a bath containing the continuously stirred liquid
• 3 calibration points (65-85-123°C)
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for temperature sensors (list of products).

DAkkS calibration temperature sensors 5-point (order code ZC0014)

• DKD/DAkkS certificate (DAkkS = Deutsche Akkreditierungsstelle)
• Comparative calibration in a bath containing the continuously stirred liquid
• 5 calibration points (20-65-85-100-123°C)
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for temperature sensors (list of products).

DAkkS calibration temperature sensors N-point (order code ZC0015)

• DKD/DAkkS certificate (DAkkS = Deutsche Akkreditierungsstelle)
• Comparative calibration in a bath containing the continuously stirred liquid
• Number (max. 4) and position of the calibration points according to the customer request (temperature range: -20°C...150°C)
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for temperature sensors  (list of products).

ISO calibration temperature sensors 3-point (oder code ZC0016)

• Calibration certificate
• Comparative calibration in a bath containing the continuously stirred liquid
• 3 calibration points (65-85-123°C)
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for temperature sensors  (list of products).

ISO-Kalibrierung Temperatursensoren 5-Punkt (Bestellcode ZC0017)

• Calibration certificate
• Comparative calibration in a bath containing the continuously stirred liquid
• 5 calibration points (20-65-85-100-123°C)
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for temperature sensors (list of products).

ISO calibration temperature sensors N-point (order code ZC0018)

• Calibration certificate
• Comparative calibration in a bath containing the continuously stirred liquid
• Number (max. 4) and position of the calibration points according to the customer request (temperature range: -20°C...150°C)
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for temperature sensors (list of products).

Cleaning for oxygen applications​ (order code ZC0019)

• Cleaning for oxygen applications (free of oil and grease).
• The cleaned units are given a special marking and packaging.
• Applies to the specified article(s) and must be requested when ordering the article.
• For each unit ZC0019 has to be ordered separately.

• Only issued for fluid sensor products  (list of products).

ISO calibration protocol SD (order code ZC0020)

• Calibration certificate
• Comparative calibration with standard reference
• Calibration at 6 flow values (depending on the nominal diameter)
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for flow sensors (list of products).

ISO calibration SM (order code ZC0052)

• Calibration certificate
• Comparative calibration with standard reference
• Calibration at 3/4 flow values (depending on the nominal diameter)
• The calibration is carried out in factory setting.
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for flow sensors (list of products)

ISO calibration SU (order code ZC0053)

• Calibration certificate
• Comparative calibration with standard reference
• Calibration at 4 flow values (depending on the nominal diameter)
• The calibration is carried out in factory setting.
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for flow sensors (list of products)

Factory calibration for infra-red temperature sensors (order code ZC0061)

• Calibration certificate
• Created according to the requirements of DIN EN ISO 9001:2008
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible when giving the serial number. The certificate will then be dated with the day of calibration.

• Only issued for temperature sensors (list of products).

Recalibration for infra-red temperature sensor TW20xx (order code ZC0062)

• Calibration certificate
• Created according to the requirements of DIN EN ISO 9001:2008
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s).

• Only issued for temperature sensors (list of products).

Recalibration for infra-red temperature sensor TW2002 (order code ZC0063)

• Calibration certificate
• Created according to the requirements of DIN EN ISO 9001:2008
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s).

• Only issued for temperature sensors (list of products).

A2LA calibration temperature sensors 3-point​ (order code ZC0064)

• Calibration certificate
• Created according to A2LA / ILAC MRA
• Comparative calibration in a bath containing the continuously stirred liquid
• 3 calibration points (65-85-123°C)
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for temperature sensors (list of products).

A2LA calibration temperature sensors 5-point  (order code ZC0065) 

• Calibration certificate
• Created according to A2LA / ILAC MRA
• Comparative calibration in a bath containing the continuously stirred liquid
• 5 calibration points (20-65-85-100-123°C)
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for temperature sensors (list of products).

A2LA calibration temperature sensors N-point​ (order code ZC0066)

• Calibration certificate
• Created according to A2LA / ILAC MRA
• Comparative calibration in a bath containing the continuously stirred liquid
• Number (max. 4) and position of the calibration points according to the customer request (temperature range: -20°C...200°C)
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for temperature sensors (list of products).

Recalibration for oil particle counter LDP (order code ZC0069)

• Calibration certificate
• Created according to the requirements of DIN EN ISO 9001:2008
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s).

• Only issued for oil particle counter (list of products).

DAkkS calibration flow sensors 6-point (order code ZC0075)

• DKD/DAkkS certificate (DAkkS = Deutsche Akkreditierungsstelle)
• Comparative calibration with standard reference
• Calibration at 6 flow values (depending on the nominal diameter)
• The calibration is carried out in factory setting using the analogue output (current). Alternatively visually via display or analogue output (voltage).
• Recalibrations are only possible if subjected unit is returned. The unit shall be in a clean state, without adaptations (condition as supplied to the customer). The declaration of decontamination has to be included.
• The document is bilingual (German / English).
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

• Only issued for flow sensors (list of products).

INMETRO calibration protocol temperature sensors (order code ZBR001)

• Calibration certificate
• Created according to INMETRO regulations
• The document is available in Portuguese.  
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

INMETRO calibration protocol flow sensors (order code ZBR002)

• Calibration certificate
• Created according to INMETRO regulations
• The document is available in Portuguese. 
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.

INMETRO calibration protocol pressure sensors  (order code ZBR003)

• Calibration certificate
• Created according to INMETRO regulations
• The document is available in Portuguese. 
• Applies to the specified article(s) and must be requested when ordering the article.
• Subsequent orders are only possible if subjected unit is returned.