| Product characteristics |
| Number of inputs and outputs |
Number of digital outputs: 2; Number of analogue outputs: 1 |
| Process connection |
G 3/4 DN20 flat seal |
| Application |
| Special feature |
Gold-plated contacts |
| Media |
conductive liquids; water; hydrous media |
| Note on media |
| conductivity: ≥ 20 µS/cm |
| viscosity: < 70 mm²/s (40 °C) |
|
| Medium temperature [°C] |
-20...90 |
| Pressure rating [bar] |
16 |
| Electrical data |
| Operating voltage [V] |
18...30 DC; (to SELV/PELV) |
| Current consumption [mA] |
< 80 |
| Protection class |
III |
| Reverse polarity protection |
yes |
| Power-on delay time [s] |
5 |
| Inputs / outputs |
| Number of inputs and outputs |
Number of digital outputs: 2; Number of analogue outputs: 1 |
| Inputs |
| Inputs |
counter reset |
| Outputs |
| Total number of outputs |
2 |
| Output signal |
switching signal; analogue signal; pulse signal; IO-Link; frequency signal; (configurable) |
| Electrical design |
PNP/NPN |
| Number of digital outputs |
2 |
| Output function |
normally open / normally closed; (parameterisable) |
| Max. voltage drop switching output DC [V] |
2 |
| Permanent current rating of switching output DC [mA] |
100 |
| Number of analogue outputs |
1 |
| Analogue current output [mA] |
4...20; (scalable) |
| Max. load [Ω] |
500 |
| Pulse output |
flow rate meter |
| Short-circuit protection |
yes |
| Type of short-circuit protection |
pulsed |
| Overload protection |
yes |
| Measuring/setting range |
| Measuring range |
| 0.1...75 l/min |
0.006...4.5 m³/h |
1.2...1190 gph |
0.02...19.82 gpm |
|
| Display range |
| -90...90 l/min |
-5.4...5.4 m³/h |
-1426.8...1426.8 gph |
-23.78...23.78 gpm |
|
| Resolution |
| 0.1 l/min |
0.006 m³/h |
0.6 gph |
0.01 gpm |
|
| Set point SP |
| 0.5...75 l/min |
0.03...4.5 m³/h |
8.4...1189 gph |
0.14...19.81 gpm |
|
| Reset point rP |
| 0.1...74.6 l/min |
0.006...4.48 m³/h |
1.2...1183 gph |
0.03...19.71 gpm |
|
| Analogue start point ASP |
| 0...59.9 l/min |
0...3.6 m³/h |
0...950 gph |
0...15.82 gpm |
|
| Analogue end point AEP |
| 15.1...75 l/min |
0.9...4.5 m³/h |
240...1189 gph |
3.99...19.81 gpm |
|
| Low flow cut-off LFC |
| 0.1...3.8 l/min |
0.006...0.23 m³/h |
1.8...59.4 gph |
0.03...0.99 gpm |
|
| Frequency end point, FEP |
| 15.1...75 l/min |
0.9...4.5 m³/h |
240...1189 gph |
3.99...19.81 gpm |
|
| Frequency at the end point FRP [Hz] |
1...10000 |
| Volumetric flow quantity monitoring |
| Pulse length [s] |
0.003...2 |
| Pulse value |
0.01...99990000 I |
| Temperature monitoring |
| Measuring range [°C] |
-20...90 |
| Display range [°C] |
-42...112 |
| Resolution [°C] |
0.1 |
| Set point SP [°C] |
-19.6...90 |
| Reset point rP [°C] |
-20...89.6 |
| Analogue start point [°C] |
-20...68 |
| Analogue end point [°C] |
2...90 |
| In steps of [°C] |
0.1 |
| Accuracy / deviations |
| Flow monitoring |
| Accuracy (in the measuring range) |
± (0,8 % MW + 0,2 % MEW) |
| Repeatability |
± 0,2 % MEW |
| Temperature monitoring |
| Accuracy [K] |
± 2,5 (Q > 5 % MEW) |
| Response times |
| Flow monitoring |
| Start-up delay [s] |
0...50 |
| Response time [s] |
< 0.25; (dAP = 0, T09) |
| Damping process value dAP [s] |
0...5 |
| Temperature monitoring |
| Response time [s] |
15; (Q > 10 % MEW, T09) |
| Software / programming |
| Parameter setting options |
hysteresis / window; normally open / normally closed; switching logic; frequency output; current/pulse output; start-up delay; display can be deactivated; Display unit |
| Interfaces |
| Communication interface |
IO-Link |
| Transmission type |
COM2 (38,4 kBaud) |
| IO-Link revision |
1.1 |
| SDCI standard |
IEC 61131-9 |
| Profiles |
Smart Sensor: Process Data Variable; Device Identification, Device Diagnosis |
| SIO mode |
yes |
| Required master port type |
A |
| Process data analogue |
3 |
| Process data binary |
2 |
| Min. process cycle time [ms] |
6 |
| Supported DeviceIDs |
| Type of operation |
DeviceID |
| Default |
955 |
|
| Operating conditions |
| Ambient temperature [°C] |
-20...60 |
| Storage temperature [°C] |
-25...80 |
| Protection |
IP 65; IP 67 |
| Tests / approvals |
| EMC |
|
| CPA approval |
| model number |
006MI |
| accuracy class |
- |
| maximum allowable error |
± 1,0 % FS |
| Q (min) |
0,006 m³/h |
| Q (t) |
- |
| Q (max) |
4,5 m³/h |
|
| Shock resistance |
| DIN IEC 68-2-27 |
20 g (11 ms) |
|
| Vibration resistance |
| DIN IEC 68-2-6: |
5 g (10...2000 Hz) |
|
| MTTF [years] |
114 |
| UL approval |
| UL Approval no. |
I014 |
| File number UL |
E174189 |
|
| Pressure Equipment Directive |
Sound engineering practice; can be used for group 2 fluids; group 1 fluids on request |
| Mechanical data |
| Weight [g] |
798 |
| Materials |
stainless steel (1.4408/316); stainless steel (1.4404 / 316L); PC; PBT+PC-GF30 |
| Materials (wetted parts) |
stainless steel (1.4404 / 316L); PEEK; carbon fibre PEEK; EPDM; Centellen |
| Process connection |
G 3/4 DN20 flat seal |
| Displays / operating elements |
| Display |
|
colour display 1,44", 128 x 128 pixels |
|
2 x LED, yellow |
|
| Remarks |
| Remarks |
| MW = measured value |
| MEW = Final value of the measuring range |
|
| Pack quantity |
1 pcs. |
| Electrical connection |
| Connection |
Connector: 1 x M12; coding: A; Contacts: gold-plated |
| Diagrams and graphs |
|
|
|
Pressure loss / volumetric flow quantity |
|
